{"id":4148,"date":"2026-07-10T10:45:22","date_gmt":"2026-07-10T10:45:22","guid":{"rendered":"https:\/\/fsxchemical.com\/?p=4148"},"modified":"2026-08-05T10:26:57","modified_gmt":"2026-08-05T10:26:57","slug":"how-to-choose-polyester-printing-paste-globally-used-process-compatibility-fastness-optimization-solutions-with-pitfall-avoidance-tips","status":"publish","type":"post","link":"https:\/\/fsxchemical.com\/ru\/blog\/how-to-choose-polyester-printing-paste-globally-used-process-compatibility-fastness-optimization-solutions-with-pitfall-avoidance-tips\/","title":{"rendered":"Key Factors Affecting Viscosity in Textile Printing Pastes"},"content":{"rendered":"<p class=\"wp-block-wd-paragraph wd-2969a823\"><em>Printing-paste viscosity is influenced by thickener chemistry, concentration, hydration, water quality, pH, temperature, mixing, formulation components and storage conditions. This guide explains how textile printers can control these variables and compare thickener grades under repeatable test conditions.<\/em><\/p>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-cd141be8\">Viscosity is one of the most frequently checked properties in textile printing paste. It affects paste preparation, pumping, screen passage, transfer to the fabric, penetration, outline definition and stability during production.<\/p>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-ff3fe5f2\">However, printing-paste viscosity is not controlled by the thickener alone. The measured value can change with concentration, water quality, pH, temperature, mixing conditions, formulation ingredients, resting time and the test method itself.<\/p>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-ab15a938\">This means that a viscosity difference does not automatically indicate a defective thickener. Before changing a supplier or rejecting a batch, technical teams should identify which variable changed and repeat the test under controlled conditions.<\/p>\n\n\n\n<h2 class=\"wp-block-wd-title title wd-a0d38c3a\">Why Viscosity Matters in Textile Printing<\/h2>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-b605303a\">A printing paste must remain stable before use, move through the printing equipment under shear and recover sufficiently after it is transferred to the fabric. If the paste is too fluid under the relevant conditions, it may spread beyond the intended design or penetrate differently from the approved production standard.<\/p>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-1d79c2ce\">If the paste is too resistant to flow, it may be difficult to mix, filter, pump or transfer through the screen. Excessive resistance can also affect paste release and make machine cleaning more difficult.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-93f2c73f\">Low apparent viscosity may be associated with<\/h3>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Insufficient thickener dosage<\/li>\n\n\n\n<li>Incomplete hydration<\/li>\n\n\n\n<li>Unexpected electrolyte or alkali effects<\/li>\n\n\n\n<li>High sample temperature<\/li>\n\n\n\n<li>Excessive dilution<\/li>\n\n\n\n<li>Prolonged or unsuitable mechanical shear<\/li>\n\n\n\n<li>Incompatible formulation components<\/li>\n\n\n\n<li>Incorrect viscosity-measurement conditions<\/li>\n<\/ul>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-55dd8ddb\">High apparent viscosity may be associated with<\/h3>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Excessive thickener dosage<\/li>\n\n\n\n<li>Lower-than-normal sample temperature<\/li>\n\n\n\n<li>Longer hydration or resting time<\/li>\n\n\n\n<li>Water-loss or evaporation during storage<\/li>\n\n\n\n<li>An incorrect weighing or concentration calculation<\/li>\n\n\n\n<li>A different thickener grade or batch<\/li>\n\n\n\n<li>Changes in the measurement spindle or rotational speed<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-cce86eca\">These symptoms are useful starting points, but they do not identify the cause by themselves. The complete formulation and testing history should be reviewed before corrective action is taken.<\/p>\n\n\n\n<h2 class=\"wp-block-wd-title title wd-853a21c5\">Viscosity Is Not the Same as Complete Rheological Performance<\/h2>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-87b5edd9\">A single viscosity number describes the result measured under one defined condition. It does not fully describe how a printing paste behaves during mixing, pumping, screen passage, transfer and recovery on the fabric.<\/p>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-d428cf7d\">Many textile printing pastes show non-Newtonian behavior. Their apparent viscosity changes when the applied shear condition changes. A paste may appear thick while standing but flow more easily when it is mixed or forced through a screen.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-57acde2d\">Shear-thinning behavior<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-af0dc2aa\">In a shear-thinning system, apparent viscosity decreases as shear increases. This behavior can help a paste move through production equipment while still providing sufficient body under lower-shear conditions.<\/p>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-3a35f86b\">Two grades can therefore produce a similar reading at one rotational speed but behave differently at another speed or in the printing machine. Comparing only one number may overlook an important application difference.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-8a082e23\">Structural recovery<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-c38130fd\">After passing through the screen or coating equipment, the paste should recover enough structure to support the intended print outline and penetration. Recovery that is too slow or too limited may contribute to spreading, while excessive structure can affect leveling and transfer.<\/p>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-bbbfc855\">The preferred rheological profile depends on the printing method, screen, fabric, color system and design. There is no universal viscosity target suitable for every textile printing process.<\/p>\n\n\n\n<h2 class=\"wp-block-wd-title title wd-10344c9e\">1. Thickener Chemistry and Grade<\/h2>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-9b78eee3\">Thickener chemistry is one of the main factors determining viscosity, hydration, electrolyte response and flow behavior. Even products in the same chemical family may have different commercial specifications and application characteristics.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-23686baf\">\u0410\u043b\u044c\u0433\u0438\u043d\u0430\u0442 \u043d\u0430\u0442\u0440\u0438\u044f<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-a4310376\"><a href=\"https:\/\/fsxchemical.com\/ru\/product\/%d0%b0%d0%bb%d1%8c%d0%b3%d0%b8%d0%bd%d0%b0%d1%82-%d0%bd%d0%b0%d1%82%d1%80%d0%b8%d1%8f\/\">\u0410\u043b\u044c\u0433\u0438\u043d\u0430\u0442 \u043d\u0430\u0442\u0440\u0438\u044f<\/a> is commonly evaluated as a thickener for reactive dye printing. Different grades can vary in viscosity, solution behavior, filtration performance and suitability for specific paste formulations.<\/p>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-d056755f\">A sodium alginate grade should be selected according to the required application rather than viscosity alone. Dye system, electrolyte level, preparation conditions, screen performance, fixation and wash-off should be considered together.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-81a62650\">\u041a\u0430\u0440\u0431\u043e\u043a\u0441\u0438\u043c\u0435\u0442\u0438\u043b\u0446\u0435\u043b\u043b\u044e\u043b\u043e\u0437\u0430<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-26b50ecc\"><a href=\"https:\/\/fsxchemical.com\/ru\/product\/%d0%ba%d0%b0%d1%80%d0%b1%d0%be%d0%ba%d1%81%d0%b8%d0%bc%d0%b5%d1%82%d0%b8%d0%bb%d1%86%d0%b5%d0%bb%d0%bb%d1%8e%d0%bb%d0%be%d0%b7%d0%b0-cmc\/\">\u041a\u0430\u0440\u0431\u043e\u043a\u0441\u0438\u043c\u0435\u0442\u0438\u043b\u0446\u0435\u043b\u043b\u044e\u043b\u043e\u0437\u0430 (CMC)<\/a> is available in different viscosity, substitution and purity ranges. These differences may influence hydration, solution clarity, salt tolerance and compatibility with other formulation components.<\/p>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-ddf1f9bf\">A CMC grade used in one textile process should not automatically be transferred to another process without testing. Printing, sizing and auxiliary formulations may require different grade characteristics.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-722914b8\">\u041a\u0430\u0440\u0431\u043e\u043a\u0441\u0438\u043c\u0435\u0442\u0438\u043b\u043a\u0440\u0430\u0445\u043c\u0430\u043b<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-675044d3\"><a href=\"https:\/\/fsxchemical.com\/ru\/product\/%d0%ba%d0%b0%d1%80%d0%b1%d0%be%d0%ba%d1%81%d0%b8%d0%bc%d0%b5%d1%82%d0%b8%d0%bb%d0%ba%d1%80%d0%b0%d1%85%d0%bc%d0%b0%d0%bb-cms\/\">\u041a\u0430\u0440\u0431\u043e\u043a\u0441\u0438\u043c\u0435\u0442\u0438\u043b\u043a\u0440\u0430\u0445\u043c\u0430\u043b (CMS)<\/a> may be used in selected textile printing and sizing formulations. Its performance depends on the grade, concentration, preparation method and compatibility with the complete chemical system.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-72bc55a9\">Compound thickeners and digital printing pastes<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-69ed990a\">Compound thickeners may combine different materials to create a particular balance of hydration, rheology, filtration and cost in use. The performance of a compound product cannot be predicted from a single viscosity value.<\/p>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-aed600df\">For digital pretreatment applications, a dedicated <a href=\"https:\/\/fsxchemical.com\/ru\/product\/%d0%bf%d0%b0%d1%81%d1%82%d0%b0-%d0%b4%d0%bb%d1%8f-%d1%86%d0%b8%d1%84%d1%80%d0%be%d0%b2%d0%be%d0%b9-%d0%bf%d0%b5%d1%87%d0%b0%d1%82%d0%b8\/\">\u043f\u0430\u0441\u0442\u0430 \u0434\u043b\u044f \u0446\u0438\u0444\u0440\u043e\u0432\u043e\u0439 \u043f\u0435\u0447\u0430\u0442\u0438<\/a> may need to balance viscosity with filtration, coating uniformity, fabric penetration and compatibility with the selected ink and pretreatment process.<\/p>\n\n\n\n<h2 class=\"wp-block-wd-title title wd-4fa532cf\">2. Thickener Concentration<\/h2>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-80c588a5\">Thickener concentration has a direct influence on apparent viscosity, but the relationship is not always linear. A relatively small dosage change can produce a noticeable viscosity difference, especially in concentrated polymer systems.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-8f2df72e\">Use the same concentration basis<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-50cc0524\">Concentration should be reported clearly as weight percentage or another agreed basis. The laboratory should also define whether the calculation is based on the supplied product, dry matter or active content.<\/p>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-543babb8\">Comparing one sample at 2% with another at 2.5% does not provide a like-for-like grade comparison. The reference and candidate should first be tested at the same concentration and under the same preparation conditions.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-9ea571b4\">Check weighing and total batch volume<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-ea5bfa58\">Incorrect weighing, incomplete transfer from the container or inconsistent final batch weight can change the real concentration. These preparation errors may be mistaken for product inconsistency.<\/p>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-01f9380a\">For laboratory comparisons, use calibrated weighing equipment, identical containers and a recorded preparation sheet.<\/p>\n\n\n\n<h2 class=\"wp-block-wd-title title wd-fb6c45e6\">3. Dispersion and Hydration<\/h2>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-8870a54a\">Powdered thickeners need to disperse and hydrate before their expected viscosity develops. Poor dispersion can create lumps with a hydrated surface and a dry interior, reducing the effective amount of thickener available to build viscosity.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-a6c341a2\">\u0412\u0440\u0435\u043c\u044f \u0433\u0438\u0434\u0440\u0430\u0442\u0430\u0446\u0438\u0438<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-c74c04b3\">Some grades develop viscosity quickly, while others require a longer mixing or resting period. Measuring one sample immediately and another after complete hydration can create an artificial difference.<\/p>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-c9b87113\">The preparation procedure should define mixing time, resting time and the point at which the sample is considered ready for measurement.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-678291f5\">Powder-addition rate<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-82c91822\">Adding powder too quickly can promote lump formation. A controlled addition rate and sufficient liquid movement usually provide a more uniform dispersion.<\/p>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-6f5fb2a9\">The suitable method depends on the product form, equipment and batch size. Follow the grade-specific preparation guidance supplied in the TDS or application instructions.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-1c9201cd\">Particle-size effects<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-2e0ca310\">Particle size can influence wetting, dusting, dispersion and hydration speed. A faster-hydrating grade may not always be the best choice if the available mixing system cannot disperse it uniformly.<\/p>\n\n\n\n<h2 class=\"wp-block-wd-title title wd-cf9d143e\">4. Water Quality and Electrolytes<\/h2>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-9bbd0411\">Water is a major part of most textile printing pastes. Changes in hardness, dissolved salts, conductivity or contamination can influence thickener hydration and apparent viscosity.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-1cf13583\">Hardness and dissolved ions<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-c6506d8c\">Calcium, magnesium and other dissolved ions may interact differently with different thickener systems. A grade that performs consistently in laboratory water may behave differently in factory process water.<\/p>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-ef24f11d\">When unexplained viscosity changes occur, compare the water source, conductivity, hardness and treatment condition used for the approved and affected batches.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-adbb719f\">Added salts and electrolytes<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-952d7042\">Reactive printing and other textile formulations may contain salts, alkalis or ionic auxiliaries. These materials can alter polymer-chain interactions and change the apparent viscosity of the final paste.<\/p>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-e676bbc1\">Salt tolerance should therefore be evaluated in the complete formulation, not only in a thickener-and-water solution.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-1921be1c\">Use actual process water during approval<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-1dc14455\">Supplier screening can begin with controlled laboratory water, but final grade approval should include the buyer&#8217;s actual process water where practical. This reduces the risk of differences between laboratory and production performance.<\/p>\n\n\n\n<h2 class=\"wp-block-wd-title title wd-3c4c12c5\">5. pH, Alkali and Chemical Compatibility<\/h2>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-93089481\">Changes in pH can affect the hydration, stability and flow behavior of some printing-paste systems. Alkali can also influence other ingredients in the formulation, producing an indirect viscosity change.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-319cc3c6\">Record pH at the correct preparation stage<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-ac2a872f\">The pH of the thickener stock paste may differ from the pH after dyes, binders, alkalis and auxiliaries are added. For troubleshooting, record both the preparation stage and the time at which the pH was measured.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-954b5ba8\">Avoid assuming that all grades have the same pH tolerance<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-5ce40864\">Different thickener chemistries and grades can respond differently to acidic, neutral or alkaline conditions. Supplier information can be used for initial screening, but the complete production formulation should still be tested.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-d2660018\">Check for delayed changes<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-84f116dd\">Some incompatibility problems are not visible immediately after mixing. Measure the paste after the normal factory holding time to identify delayed thinning, thickening, separation or sedimentation.<\/p>\n\n\n\n<h2 class=\"wp-block-wd-title title wd-704c3feb\">6. Temperature<\/h2>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-1f61a23a\">Temperature affects both polymer hydration and the viscosity measurement. In many liquid systems, a warmer sample gives a lower apparent viscosity reading than the same sample measured at a cooler temperature.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-5e02d8ff\">Control measurement temperature<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-6b22348f\">Supplier and buyer results should not be compared unless the measurement temperatures are known. Even when the same instrument and spindle are used, a temperature difference can produce a different result.<\/p>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-2eec75af\">The test method should state the target temperature and the acceptable range before measurement.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-b585991e\">Consider preparation temperature<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-9e9b3eca\">Water temperature can influence wetting and hydration speed. Excessively cold or hot water may produce different preparation behavior from the supplier&#8217;s recommended method.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-9127febd\">Monitor factory conditions<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-877d28d3\">Seasonal temperature changes, heat generated during high-speed mixing and warm production areas can all affect paste readings. Temperature should be recorded whenever viscosity trends are compared over time.<\/p>\n\n\n\n<h2 class=\"wp-block-wd-title title wd-1b9a073d\">7. Mixing Speed, Time and Shear<\/h2>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-44652ed3\">Mixing provides the movement needed to wet, disperse and hydrate a thickener. However, different impellers, vessel shapes, batch sizes and rotational speeds create different shear conditions.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-77b68666\">Insufficient mixing<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-7816e54a\">Insufficient mixing may leave dry particles, lumps or nonuniform regions. The measured viscosity may then depend on where the sample is taken from the container.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-3df3cac3\">Excessive mechanical treatment<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-780a7cba\">Prolonged or unnecessarily intense mixing may change the structure or temperature of the paste. The effect depends on the thickener chemistry, formulation and equipment.<\/p>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-a18e8f28\">A laboratory mixer operating at the same displayed speed as a production mixer does not necessarily produce the same shear environment. Scale-up should therefore be confirmed through a production-relevant trial.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-67f762e5\">Standardize the mixing procedure<\/h3>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Record mixer type and impeller design<\/li>\n\n\n\n<li>Record rotational speed or equipment setting<\/li>\n\n\n\n<li>Use the same container size for comparative tests<\/li>\n\n\n\n<li>Define mixing and resting times<\/li>\n\n\n\n<li>Monitor sample temperature after mixing<\/li>\n\n\n\n<li>Record the batch size and filling level<\/li>\n<\/ul>\n\n\n\n<h2 class=\"wp-block-wd-title title wd-21ea0b64\">8. Order of Addition<\/h2>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-a73d69c9\">The sequence in which water, thickener, dyes, pigments, salts, alkalis, binders and auxiliaries are added can influence dispersion and final viscosity.<\/p>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-8297fb94\">Adding an electrolyte before a polymer is fully hydrated may produce a different result from adding the same electrolyte after stock-paste preparation. A binder or auxiliary may also interfere with wetting if it is introduced too early.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-921cea01\">Use a written preparation sequence<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-f90561ed\">A reliable formulation should include more than a list of ingredients. It should specify the order of addition, mixing time after each step, temperature and resting period.<\/p>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-1d3faed3\">When troubleshooting, compare the actual operator procedure with the approved written procedure. Changes made for convenience during production can be an overlooked source of viscosity variation.<\/p>\n\n\n\n<h2 class=\"wp-block-wd-title title wd-8cf862af\">9. Dyes, Pigments, Binders and Auxiliaries<\/h2>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-03c6eb64\">A thickener is only one component of a printing paste. Colorants, binders, alkalis, salts, humectants, defoamers, preservatives and other auxiliaries can change viscosity or flow behavior.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-66bf7e90\">Dyes and pigments<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-97cbe0dd\">Different dye or pigment preparations may introduce salts, dispersing agents, solvents or other components into the paste. Changing the colorant supplier or concentration can therefore affect the final viscosity even when the thickener remains unchanged.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-2c96cb39\">Binders<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-f054694d\">Pigment-printing binders can interact with thickeners and other auxiliaries. Compatibility should be evaluated in the complete pigment paste at the intended binder concentration.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-b7eecefc\">Defoamers, wetting agents and other auxiliaries<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-74478c69\">Some auxiliaries can change surface behavior, dispersion or the measured rheology of the formulation. An auxiliary should not automatically be assumed neutral to viscosity because it is used at a relatively low dosage.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-2df767c4\">Preservatives and microbial condition<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-5779cb84\">Water-based pastes stored for extended periods may require appropriate microbial control. Contamination can cause odor, gas formation, separation or viscosity loss in susceptible formulations.<\/p>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-47806311\">Preservative selection and use should follow the applicable product, workplace and regulatory requirements. Do not add or change a preservative without a controlled compatibility review.<\/p>\n\n\n\n<h2 class=\"wp-block-wd-title title wd-5eaa3b60\">10. Resting Time, Storage and Paste Age<\/h2>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-39b0ef8c\">Printing-paste viscosity may continue to change after mixing. Some systems need a defined resting period to complete hydration, while others may gradually lose or gain apparent viscosity during storage.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-10804f2c\">Measure at agreed time points<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-1c863b08\">For meaningful comparison, define when the first reading will be taken. Useful checkpoints may include immediately after preparation, after the standard hydration period and after the normal production holding time.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-b705808d\">Control evaporation<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-6f4ee18c\">An uncovered container can lose water and become more concentrated. Evaporation may be incorrectly interpreted as thickener development or batch variation.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-e0fc8141\">Record storage conditions<\/h3>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Container type and closure<\/li>\n\n\n\n<li>Storage temperature<\/li>\n\n\n\n<li>Preparation date and time<\/li>\n\n\n\n<li>Paste age at measurement<\/li>\n\n\n\n<li>Agitation before sampling<\/li>\n\n\n\n<li>Visible separation, settling or surface skin<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-b972cde3\">Old paste should not be compared directly with newly prepared paste unless ageing is the specific subject of the test.<\/p>\n\n\n\n<h2 class=\"wp-block-wd-title title wd-7ea8e62d\">11. Raw-Material and Batch Variation<\/h2>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-ca83119a\">Industrial thickeners are supplied according to agreed specifications, but normal batch variation can still exist within those limits. The practical question is whether the variation remains acceptable for the customer&#8217;s formulation and process.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-6844cb39\">Review the Certificate of Analysis<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-67799ce2\">The batch COA may report selected properties such as viscosity, moisture, pH or other agreed parameters. Buyers should confirm that the reported viscosity method matches the method defined in the specification.<\/p>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-ea606444\">A batch cannot be compared correctly when one COA reports viscosity at one concentration and another document uses a different concentration or instrument condition.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-18f3843e\">Use incoming inspection<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-a9696326\">Incoming inspection can include package condition, batch identity, appearance, a standardized viscosity test and, where necessary, a small application test.<\/p>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-a31609da\">High-risk or newly approved grades may require closer monitoring during the first commercial deliveries before the normal inspection frequency is established.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-a81fd0fc\">Retain representative samples<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-293a2679\">Retained samples can help determine whether a later production problem is related to the supplied batch, storage conditions or the customer&#8217;s formulation process.<\/p>\n\n\n\n<h2 class=\"wp-block-wd-title title wd-a1a24be7\">12. Viscosity Measurement Method<\/h2>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-db8266a7\">A viscosity value is incomplete unless the test conditions are stated. Concentration, temperature, instrument, spindle, rotational speed, hydration time and reading procedure can all change the reported result.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-f985d8ce\">Information required for a repeatable viscosity test<\/h3>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Product concentration and calculation basis<\/li>\n\n\n\n<li>Water source and water quality<\/li>\n\n\n\n<li>Preparation temperature<\/li>\n\n\n\n<li>Mixer type, speed and mixing time<\/li>\n\n\n\n<li>Hydration or resting time<\/li>\n\n\n\n<li>\u0422\u0435\u043c\u043f\u0435\u0440\u0430\u0442\u0443\u0440\u0430 \u0438\u0437\u043c\u0435\u0440\u0435\u043d\u0438\u044f<\/li>\n\n\n\n<li>Viscometer model or measurement principle<\/li>\n\n\n\n<li>Spindle, rotor or geometry<\/li>\n\n\n\n<li>Rotational speed or shear condition<\/li>\n\n\n\n<li>Sample container and filling level<\/li>\n\n\n\n<li>Time allowed before recording the reading<\/li>\n\n\n\n<li>Reported unit<\/li>\n<\/ul>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-fdd0ce7a\">Do not compare results from different methods directly<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-6ac4631e\">A value measured with one instrument, spindle or speed should not be treated as equivalent to a value obtained using another method. Supplier and buyer values may both be correct within their own procedures while still appearing different.<\/p>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-6ef98e01\">When a dispute occurs, prepare the reference and questioned samples together and test them using one agreed method. This side-by-side procedure is usually more useful than comparing isolated COA numbers.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-c8b92d75\">Sample location matters<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-cfcf2e47\">A nonuniform or settled paste can give different readings from the top, middle and bottom of the container. Define whether the sample should be mixed before testing and how it should be transferred to the measurement vessel.<\/p>\n\n\n\n<h2 class=\"wp-block-wd-title title wd-adac554c\">How to Troubleshoot Printing-Paste Viscosity<\/h2>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-7f0703c9\">Viscosity troubleshooting should begin with process verification rather than an immediate dosage adjustment. Adding more thickener may temporarily change the reading without correcting the original cause.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>Observed Issue<\/th><th>Possible Factors to Check<\/th><th>Recommended First Action<\/th><\/tr><\/thead><tbody><tr><td>Viscosity is lower than the approved standard<\/td><td>Concentration, incomplete hydration, high temperature, water quality, salts, alkali, excessive dilution or test settings<\/td><td>Reprepare the reference and affected sample using the same water, temperature and test method.<\/td><\/tr><tr><td>Viscosity is higher than expected<\/td><td>Excess dosage, low temperature, water evaporation, longer resting time or incorrect spindle and speed<\/td><td>Verify weighing records, sample temperature, storage condition and instrument settings.<\/td><\/tr><tr><td>Paste contains lumps<\/td><td>Rapid powder addition, insufficient liquid movement, unsuitable addition sequence or poor wetting<\/td><td>Review the powder-addition rate, mixing pattern and hydration instructions.<\/td><\/tr><tr><td>Paste is stable in water but thins after auxiliaries are added<\/td><td>Electrolyte response, pH change or chemical incompatibility<\/td><td>Add each component separately in a controlled compatibility test.<\/td><\/tr><tr><td>Laboratory viscosity is acceptable but machine behavior is poor<\/td><td>Inadequate rheological profile, shear recovery, filtration, machine shear or scale-up difference<\/td><td>Compare performance under several test speeds and conduct a production-relevant application trial.<\/td><\/tr><tr><td>Viscosity changes during storage<\/td><td>Continued hydration, evaporation, temperature variation, contamination or delayed incompatibility<\/td><td>Measure at defined time points in closed containers and record the storage conditions.<\/td><\/tr><tr><td>Supplier and buyer results do not match<\/td><td>Different concentration, instrument, spindle, speed, temperature, hydration time or water source<\/td><td>Exchange the complete test methods and conduct a side-by-side test using one agreed procedure.<\/td><\/tr><tr><td>Only one color formulation shows abnormal viscosity<\/td><td>Dye, pigment, binder, salt or auxiliary differences<\/td><td>Compare the affected formulation with the standard formula one component at a time.<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-61a69b5d\">A practical troubleshooting sequence<\/h3>\n\n\n\n<ol class=\"wp-block-list\">\n<li>Confirm the product name, grade and batch number.<\/li>\n\n\n\n<li>Verify the weighing record and real concentration.<\/li>\n\n\n\n<li>Check the water source, temperature and preparation sequence.<\/li>\n\n\n\n<li>Confirm mixing speed, mixing time and hydration time.<\/li>\n\n\n\n<li>Review pH, salt, alkali and auxiliary additions.<\/li>\n\n\n\n<li>Check sample storage time and container condition.<\/li>\n\n\n\n<li>Confirm the viscometer, spindle, speed and temperature.<\/li>\n\n\n\n<li>Prepare the approved reference and affected sample side by side.<\/li>\n\n\n\n<li>Test the complete formulation rather than water solution alone.<\/li>\n\n\n\n<li>Conduct an application trial before making a supplier decision.<\/li>\n<\/ol>\n\n\n\n<h2 class=\"wp-block-wd-title title wd-5b0b5ea6\">What Buyers Should Check When Selecting a Thickener<\/h2>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-08ff38ff\">Buyers should not select a printing thickener using viscosity and price alone. The grade should be evaluated according to the intended fabric, colorant system, printing equipment, preparation method and final quality requirements.<\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-da940a01\">Technical information to request<\/h3>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Permanent product and grade code<\/li>\n\n\n\n<li>Current Technical Data Sheet<\/li>\n\n\n\n<li>Current Safety Data Sheet<\/li>\n\n\n\n<li>Viscosity range and complete test method<\/li>\n\n\n\n<li>Recommended concentration and preparation method<\/li>\n\n\n\n<li>pH and moisture specification where relevant<\/li>\n\n\n\n<li>Relevant substitution or purity information where applicable<\/li>\n\n\n\n<li>Filtration or residue information where required<\/li>\n\n\n\n<li>Recommended application and known limitations<\/li>\n\n\n\n<li>Representative sample for laboratory evaluation<\/li>\n<\/ul>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-a9b80d7c\">Application information to provide to the supplier<\/h3>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Fabric and fibre composition<\/li>\n\n\n\n<li>Reactive, pigment, disperse, acid or digital process<\/li>\n\n\n\n<li>\u0421\u0438\u0441\u0442\u0435\u043c\u0430 \u043a\u0440\u0430\u0441\u0438\u0442\u0435\u043b\u0435\u0439, \u043f\u0438\u0433\u043c\u0435\u043d\u0442\u043e\u0432 \u0438\u043b\u0438 \u0447\u0435\u0440\u043d\u0438\u043b<\/li>\n\n\n\n<li>Printing or coating equipment<\/li>\n\n\n\n<li>Current thickener and dosage<\/li>\n\n\n\n<li>\u0426\u0435\u043b\u0435\u0432\u0430\u044f \u0432\u044f\u0437\u043a\u043e\u0441\u0442\u044c \u0438 \u043f\u043e\u043b\u043d\u0430\u044f \u043c\u0435\u0442\u043e\u0434\u0438\u043a\u0430 \u0438\u0437\u043c\u0435\u0440\u0435\u043d\u0438\u044f<\/li>\n\n\n\n<li>Water source and relevant process conditions<\/li>\n\n\n\n<li>Current production problem<\/li>\n\n\n\n<li>Required paste holding time<\/li>\n\n\n\n<li>Final print-quality requirements<\/li>\n<\/ul>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-0f401de2\">Compare cost in use<\/h3>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-48022e64\">A higher-viscosity grade is not automatically more economical. Buyers should compare the dosage needed for acceptable application performance, hydration time, mixing requirements, filtration, machine behavior, wash-off and production consistency.<\/p>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-7ad98971\">The lowest price per kilogram may not provide the lowest total production cost if the product requires a higher dosage or creates additional processing problems.<\/p>\n\n\n\n<h2 class=\"wp-block-wd-title title wd-c2bb03e5\">How FSX Chemical Supports Viscosity Grade Matching<\/h2>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-3859080a\">FSX Chemical supplies CMC, CMS, sodium alginate and digital printing paste for different textile printing and formulation requirements. Candidate grades can be reviewed according to the customer&#8217;s process, existing product and target viscosity method.<\/p>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-26415aea\">To begin a technical review, buyers can provide the current TDS or product sample together with the fabric, printing method, formulation, dosage, water condition and viscosity test procedure\ud83d\udce7\u00a0<strong>\u042d\u043b\u0435\u043a\u0442\u0440\u043e\u043d\u043d\u0430\u044f \u043f\u043e\u0447\u0442\u0430<a href=\"https:\/\/fsxchemical.com\/ru\/%d1%81%d0%b2%d1%8f%d0%b6%d0%b8%d1%82%d0%b5%d1%81%d1%8c-%d1%81-%d0%bd%d0%b0%d0%bc%d0%b8\/\">: Service@fsxchemical.com<\/a><\/strong><\/p>\n\n\n\n<h3 class=\"wp-block-wd-title title wd-a7d171c1\">Available matching support may include<\/h3>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Review of the existing product specification or TDS<\/li>\n\n\n\n<li>Selection of a suitable starting grade<\/li>\n\n\n\n<li>Provision of the relevant TDS and SDS<\/li>\n\n\n\n<li>Representative samples for laboratory testing<\/li>\n\n\n\n<li>Guidance for side-by-side viscosity comparison<\/li>\n\n\n\n<li>Support for reviewing laboratory and application results<\/li>\n\n\n\n<li>Batch documentation for the selected commercial grade<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-wd-paragraph wd-aa79555a\">A candidate should be treated as a proposed matching grade rather than an automatically approved replacement. Final approval should be based on the customer&#8217;s controlled laboratory and production-relevant tests.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><\/p>","protected":false},"excerpt":{"rendered":"<p>Printing-paste viscosity is influenced by thickener chemistry, concentration, hydration, water quality, pH, temperature, mixing, formulation components and storage conditions. This guide explains how to control these variables and compare thickener grades under repeatable test conditions.<\/p>","protected":false},"author":1,"featured_media":0,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_acf_changed":false,"_seopress_titles_title":"Key Factors Affecting Viscosity in Textile Printing Pastes","_seopress_titles_desc":"Learn what affects viscosity in textile printing pastes, including thickener grade, dosage, water quality, pH, temperature, mixing and storage.","_seopress_robots_index":"","_seopress_robots_follow":"","_seopress_robots_imageindex":"","_seopress_robots_snippet":"","_seopress_robots_primary_cat":"","_seopress_robots_breadcrumbs":"","_seopress_robots_freeze_modified_date":"","_seopress_robots_custom_modified_date":"","_seopress_robots_canonical":"","_seopress_social_fb_title":"","_seopress_social_fb_desc":"","_seopress_social_fb_img":"","_seopress_social_fb_img_attachment_id":0,"_seopress_social_fb_img_width":0,"_seopress_social_fb_img_height":0,"_seopress_social_twitter_title":"","_seopress_social_twitter_desc":"","_seopress_social_twitter_img":"","_seopress_social_twitter_img_attachment_id":0,"_seopress_social_twitter_img_width":0,"_seopress_social_twitter_img_height":0,"_seopress_redirections_value":"","_seopress_redirections_enabled":"","_seopress_redirections_enabled_regex":"","_seopress_redirections_logged_status":"","_seopress_redirections_param":"","_seopress_redirections_type":0,"_seopress_analysis_target_kw":"","footnotes":""},"categories":[1],"tags":[1209,1287,1340,1304,1114,1124,1284],"class_list":["post-4148","post","type-post","status-publish","format-standard","hentry","category-technical-guides","tag-grade-matching","tag-printing-paste-rheology","tag-printing-paste-viscosity","tag-process-control","tag-textile-printing","tag-textile-printing-thickener","tag-viscosity-testing"],"acf":[],"_links":{"self":[{"href":"https:\/\/fsxchemical.com\/ru\/wp-json\/wp\/v2\/posts\/4148","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/fsxchemical.com\/ru\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/fsxchemical.com\/ru\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/fsxchemical.com\/ru\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/fsxchemical.com\/ru\/wp-json\/wp\/v2\/comments?post=4148"}],"version-history":[{"count":3,"href":"https:\/\/fsxchemical.com\/ru\/wp-json\/wp\/v2\/posts\/4148\/revisions"}],"predecessor-version":[{"id":10299,"href":"https:\/\/fsxchemical.com\/ru\/wp-json\/wp\/v2\/posts\/4148\/revisions\/10299"}],"wp:attachment":[{"href":"https:\/\/fsxchemical.com\/ru\/wp-json\/wp\/v2\/media?parent=4148"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/fsxchemical.com\/ru\/wp-json\/wp\/v2\/categories?post=4148"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/fsxchemical.com\/ru\/wp-json\/wp\/v2\/tags?post=4148"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}