Acrylic Thickener for Dark Pigment Shades: Why High Pigment Loading Changes Viscosity and Color Yield

High pigment loading changes more than pigment concentration. It also changes water, dispersant, surfactant, electrolyte...

Dark pigment shades are a useful stress test for acrylic thickener because increasing pigment-dispersion dosage changes more than color concentration. It can also change water, dispersant, surfactant, electrolyte and pigment solids entering the paste. Depending on the complete formulation, viscosity may decrease, increase or drift during holding. Build a pigment-loading–rheology map and verify screen transfer, color, cure, rubbing and hand. Select a dosage inside a demonstrated operating window, with suitable allowance for the intended production variation, rather than treating the lowest passing laboratory point as a universal minimum.

Why Does High Pigment Loading Change Acrylic Thickener Performance?

High pigment loading changes the chemical and physical environment of the acrylic thickener.

When more commercial pigment dispersion is added, the paste can receive more:

  • Pigment solids
  • Су
  • Dispersant
  • Surfactant
  • Electrolytes
  • pH-control chemicals

Each of these variables can change viscosity or rheology.

The final response can therefore be:

  • Lower viscosity
  • Higher viscosity
  • Similar initial viscosity but poorer holding stability
  • Similar Brookfield viscosity but different screen rheology

The correct diagnostic chain is:

Pigment Loading → Complete-Paste Rheology → Screen Transfer → Penetration → Surface Color Yield → Curing / Fastness / Hand

Do not assume that every dark shade simply needs more thickener.

Why Dark Shades Are a Useful Stress Test

Dark shades often use a higher dose of pigment dispersion than pale shades.

This makes them a practical stress test for:

  • Electrolyte tolerance
  • Surfactant sensitivity
  • Binder compatibility
  • Thickener efficiency
  • Screen-transfer uniformity

Dark solid areas also make certain defects easier to see:

  • Uneven transfer
  • Weak coverage
  • Excessive penetration
  • Surface nonuniformity
  • Edge spreading

A thickener that works in a pale shade should therefore not be approved automatically for a high-pigment black or navy formula.

Pigment Dispersion Is More Than Pigment

A commercial pigment dispersion is a formulated liquid, not pure dry pigment.

It can contain:

  • Pigment particles
  • Су
  • Anionic or nonionic dispersants
  • Wetting agents
  • Surfactants
  • Preservatives
  • pH-adjusting chemicals
  • Electrolytes

Therefore:

More Pigment Dispersion ≠ Only More Colorant.

Two black pigment dispersions with the same pigment content can still influence acrylic thickener differently because their dispersant, surfactant and salt packages differ.

For this reason, supplier changes in pigment dispersion should trigger a viscosity and compatibility recheck.

High Pigment Loading Can Lower or Raise Viscosity

The direction of viscosity change is system-specific.

Viscosity can decrease because:

  • Extra dispersion added on top of a batch can dilute the thickener; a fixed-final-mass recipe that replaces make-up water need not do so.
  • Electrolytes screen charged polyacrylate groups.
  • Surfactants disrupt associative thickening.
  • pH moves outside the ideal activation window.

Viscosity can increase because:

  • Pigment solids increase the suspended-particle volume fraction.
  • Particle crowding increases flow resistance.
  • Surfactants strengthen an associative HASE network in a certain concentration range.
  • Pigment or binder particles participate in associative thickening.

This is why the article title says high pigment loading changes viscosity rather than always lowers it.

Measure the response of the real formula.

1. Dilution from Pigment Dispersion

Whether more pigment dispersion dilutes the thickener depends on the batch mass balance. Adding it on top of an existing paste increases final mass and can lower the thickener mass fraction. In a formula made to a fixed final mass, increasing dispersion while reducing make-up water leaves the thickener mass fraction unchanged if its dose is unchanged. Carrier composition, ions and particle loading can still alter rheology.

Record each ingredient in grams per kilogram of final paste, including make-up water. Distinguish a production shade formula from an extra-addition troubleshooting experiment. A viscosity loss in a correctly mass-balanced dark shade cannot be attributed to thickener dilution without checking the actual concentration.

2. Dispersants and Surfactants

Pigment dispersants and surfactants keep pigment particles separated and wettable.

But these surface-active chemicals can change acrylic-thickener rheology.

For a conventional ASE-type thickener, they can modify the aqueous and particle environment.

For a HASE-type associative thickener, surfactants can participate directly in hydrophobic associations.

Depending on concentration, this can:

  • Increase viscosity
  • Decrease viscosity
  • Change elasticity
  • Change recovery after shear

Therefore, a high-pigment formula can move the thickener into a different surfactant-response region.

3. Electrolyte Load

Many acrylic/polyacrylate thickeners contain ionized carboxylate groups after neutralization.

Electrolytes can screen those charged groups and reduce polymer expansion.

A simplified mechanism is:

Electrolyte Load ↑ → Charge Screening ↑ → Polymer Expansion Can Decrease → Thickening Efficiency Can Fall

Dark shades can create more ionic stress if the higher pigment dose also introduces more salts or ionic dispersants.

But the effect remains grade-specific.

Hydrophobically modified systems can respond differently because associative interactions provide another rheological mechanism.

Do not assume one electrolyte-retention result applies to every acrylic thickener.

4. Pigment Solids and Particle Crowding

At higher pigment solids, the particles themselves occupy more volume inside the paste.

As particle concentration increases, interactions between particles can increase flow resistance.

This can partially offset dilution or electrolyte-related viscosity loss.

In some systems, the result can be:

More Pigment → Higher Apparent Viscosity

rather than thinning.

The particle effect depends on:

  • Pigment concentration
  • Particle size distribution
  • Dispersion quality
  • Binder particles
  • Thickener architecture

This is another reason not to diagnose dark-shade viscosity from pigment percentage alone.

5. HASE and Associative-Thickener Interaction

HASE acrylic thickeners use both pH-driven swelling and hydrophobic association.

The hydrophobic groups can associate with:

  • Other HASE chains
  • Binder particles
  • Surfactant aggregates
  • Pigment-dispersion components

High pigment loading can therefore change the associative network in both directions.

Research on associative thickeners shows that pigment, dispersant, surfactant and latex concentration can all alter rheological behavior.

The practical implication is:

HASE Dark-Shade Performance Must Be Tested with the Real Pigment and Binder System.

6. Binder-to-Pigment Ratio

Compare pigment and binder on a stated mass basis. The dose of a commercial dispersion is not the mass of pigment; the dose of a binder emulsion is not necessarily the mass of functional film-forming polymer. Use composition information for the exact supplied grade when available.

Trial recordCalculation or evidenceInterpretation limit
As-supplied dispersion and binder doseRecord each in g/kg of final paste, with the complete water balance.Equal liquid dosage does not establish equal pigment or binder content.
Pigment massDispersion dose × supplier-confirmed pigment mass fraction.Do not substitute total dispersion nonvolatile content for pigment fraction.
Functional binder massBinder dose × disclosed film-forming binder mass fraction, when confirmed.Dry residue may include non-binder ingredients; label functional content as unknown if it is not disclosed.
Complete-paste nonvolatile residueMeasure with the agreed drying procedure and record its conditions.This includes retained pigment and other nonvolatile components, not only active binder.
Printed deposit and acceptanceRecord deposited paste or dry add-on, cure conditions, shade, rubbing and hand.A recipe ratio alone does not predict the cured fabric result.

Hypothetical arithmetic, not an FSX test: 50 g/kg of a dispersion containing a confirmed 40% pigment contributes 20 g/kg pigment. A 100 g/kg binder dose with a separately confirmed 30% functional binder fraction contributes 30 g/kg binder. Their functional binder-to-pigment mass ratio is 1.5. If only total nonvolatile content is known, that functional ratio cannot be calculated. This example defines the basis; it is not a recommended ratio.

Increasing binder can also alter surfactants, ions, water balance and paste rheology. Evaluate the binder and pigment ladder together with the validated curing schedule. Cotton Incorporated describes the binder–fastness–hand trade-off; it does not prescribe a universal ratio for your pigment package.

7. pH and Neutralization

Pigment dispersions can change final paste pH.

If the acrylic thickener is pH-responsive, a dark-shade formula can move away from the grade’s most useful activation range.

Record:

  • pH after thickener activation
  • pH after pigment addition
  • pH after binder addition
  • Final paste pH
  • Holding-time pH

Do not increase thickener dosage before confirming the dark-shade paste remains inside the validated pH window.

Шолу pH and neutralization control for acrylic thickener for the activation mechanism.

8. Process Water and Hardness

High pigment loading can make an already electrolyte-sensitive system more vulnerable to variable process water.

Calcium, magnesium and dissolved salts can add to the ionic load from:

  • Pigment dispersion
  • Binder
  • Fixer

If dark shades are unstable but light shades are acceptable, test the formula in:

  • Reference low-hardness water
  • Normal plant water
  • Representative high-hardness condition if relevant

Do not assume the pigment is the only variable.

Should Dark Shades Use More Acrylic Thickener?

Not automatically.

A dark shade can require more thickener if the higher pigment loading lowers complete-paste viscosity below the approved printing window.

But more thickener may be unnecessary or harmful if:

  • Particle crowding has already raised viscosity.
  • The paste still prints cleanly at the lower Brookfield number.
  • The real problem is pH or electrolyte compatibility.
  • Higher thickener dosage worsens hand or screen transfer.

Use this sequence:

Measure Complete-Paste Rheology → Print → Then Decide Thickener Dosage

not:

Dark Shade → Automatically Add More Thickener.

How High Pigment Loading Changes Color Yield

More pigment can increase apparent color strength, but the relationship is not unlimited.

Color yield depends on:

  • Pigment amount
  • Surface pigment concentration
  • Paste deposit
  • Penetration
  • Binder film
  • Dispersion uniformity
  • Curing

If a higher pigment dose causes the paste to become too fluid, deeper penetration can reduce the pigment concentration visible at the surface.

If the paste becomes too thick, incomplete transfer can reduce actual deposited pigment.

Therefore:

More Pigment ≠ Automatically Higher Surface K/S.

Penetration vs. Surface Color

For many pigment prints, the target is enough penetration for uniform coverage without losing too much pigment below the visible surface.

Low viscosity can increase:

  • Fabric penetration
  • Reverse-side show-through
  • Edge spreading

High viscosity can reduce:

  • Screen transfer
  • Leveling
  • Coverage of textured fabrics

The preferred penetration depends on:

  • Fabric construction
  • Fabric weight
  • Design
  • Pigment shade
  • Binder system

Evaluate the printed fabric—not viscosity alone.

Screen Transfer and Solid-Area Uniformity

Dark shades frequently include large solid areas where transfer uniformity is easy to judge.

High pigment loading can change:

  • High-shear viscosity
  • Screen release
  • Squeegee pressure demand
  • Paste deposit

Check:

  • Beginning-to-end solid-area density
  • Screen filling
  • Pinholes
  • Streaks
  • Patchiness

A dark-shade paste that meets a low-shear viscosity target but produces patchy solids has not passed rheology qualification.

Fine Lines vs. Large Dark Solid Areas

Use both pattern types during testing.

Fine Lines

Reveal:

  • Post-print edge spreading under a defined drying delay
  • Spreading
  • Edge definition

Large Dark Solid Areas

Reveal:

  • Transfer uniformity
  • Coverage
  • Penetration
  • Foam / pinholes
  • Shade variation

Fine-line prints show edge behaviour under the selected deposit, fabric and drying conditions; they do not alone quantify rheological recovery time. Measure recovery separately with defined shear history and elapsed time when that parameter is required. A thickener should not be approved from one simple design only.

Black and Very Dark Shades

Black can be a particularly useful stress test because many defects are visually obvious.

Check:

  • Solid coverage
  • Surface depth
  • Uneven penetration
  • Edge spreading
  • Screen running

But black pigment dispersion from one supplier should not be assumed to represent all dark pigments.

Carbon black and other dark pigments can use different:

  • Dispersant systems
  • Surfactants
  • Particle concentrations

Qualify the actual commercial pigment used in production.

Holding-Time Stability in Dark Shades

High-pigment paste can be more sensitive to delayed interactions.

Measure:

  • Fresh viscosity
  • Intermediate viscosity
  • End-of-shift viscosity
  • pH
  • Foam
  • Separation / flocculation

A dark paste that looks stable at 10 minutes but thins or thickens strongly after several hours is not production-stable.

Compare light and dark shades at the same holding times.

Foam and Air Entrainment at High Pigment Loading

Higher pigment-dispersion dosage can increase the surfactant load in the paste.

Longer or stronger mixing can also introduce more air.

This can increase:

  • Visible foam
  • Microfoam
  • Apparent viscosity variation
  • Pinholes
  • Uneven deposit

If dark shades foam more strongly, check the pigment surfactant package and mixing before increasing defoamer blindly.

Rubbing Fastness and Binder Demand

Pigment fixation depends mainly on binder and curing.

Higher pigment loading can require review of the binder-to-pigment ratio to maintain rubbing performance.

If binder is increased, the thickener must then operate in a different:

  • Solids environment
  • Surfactant environment
  • Electrolyte environment

This is why dark-shade formulation should be evaluated as:

Pigment + Binder + Thickener + Curing

rather than adjusting pigment alone.

Fabric Hand and Total Polymer Solids

Dark shades can contain more pigment, more binder and sometimes more thickener.

This raises the total solids deposited on the textile.

Excess:

  • Binder film
  • Thickener polymer
  • Pigment solids

can contribute to a heavier or stiffer printed area.

Select a thickener dose within the verified screen-rheology and finished-fabric window. Repeat the candidate conditions with representative pigment, water, holding and machine variation before defining the production lower limit.

Do not restore the light-shade viscosity target at any cost if the dark paste prints acceptably at a different value.

Build a Light–Medium–Dark Shade Ladder

A practical qualification can use three pigment levels.

Shade LevelPurposeMain Stress
LightLow-pigment baselineReference rheology
MediumNormal production rangeRoutine compatibility
DarkHigh-pigment challengeSurfactant / electrolyte / solids stress

Keep the thickener test method, fabric, screen and curing conditions constant.

This ladder compares the tested pigment-loading points under the recorded conditions. Repeat the relevant points and intended production variation before treating the grade as robust across a wider operating window.

Use a Water-Dilution Control

For an extra-addition diagnostic, split one homogeneous reference paste into equal weighed portions. Leave A unchanged, add a weighed amount of process water to B, and add the same as-supplied mass of extra pigment dispersion to C. Record the new final mass and thickener mass fraction for every portion. B is an all-water addition control, not an exact reconstruction of the dispersion carrier.

If the dispersion water fraction is disclosed, an additional carrier-water control can be informative, but any remaining mass and carrier ingredients must also be accounted for. Without that information, similarity between B and C is consistent with dilution but does not prove dilution is the only cause; different effects can offset one another.

For the separate production shade ladder, make all batches to the same final mass, retain the intended thickener dose and subtract extra pigment dispersion from make-up water. Compare pH, conductivity where useful, fresh and held rheology, screen transfer and cured fabric. This fixed-mass experiment tests the complete formulation response rather than automatic dilution.

Build a Pigment-Loading–Viscosity Curve

Instead of testing only one light and one dark shade, build several controlled pigment levels around the production range.

For each point, record:

  • Pigment-dispersion dosage
  • Final pH
  • Fresh viscosity
  • Held viscosity
  • Foam
  • Screen result

Plot:

Pigment Loading → Complete-Paste Viscosity

Do not force the trend into a straight line.

The curve may:

  • Fall
  • Rise
  • Remain flat initially and change sharply later

This is useful production information.

Build a Thickener Working Window for Dark Shades

If the dark-shade curve leaves the approved rheology window, build a small thickener dosage ladder at the high-pigment condition.

For each thickener point, evaluate:

  • Complete-paste viscosity
  • Shear thinning
  • Recovery
  • Screen transfer
  • Түс өнімділігі
  • Hand

The objective is:

A Validated Thickener-Dosage Window at the Required Dark-Shade Performance

not:

Restore the Exact Light-Shade Brookfield Number.

  1. Define the current light and dark production formulas.
  2. Use the same thickener batch and viscosity method.
  3. Build a light–medium–dark pigment ladder.
  4. Record pH and viscosity after pigment and binder.
  5. Run a water-dilution control.
  6. Measure fresh and held viscosity.
  7. Print both fine-line and dark-solid-area patterns.
  8. Cure under identical conditions.
  9. Compare K/S, penetration, dry/wet rubbing and hand.
  10. Adjust thickener only if the dark shade leaves the approved printing window.

For a controlled current-vs-candidate comparison, FSX Chemical can review the formula through Үлгілер мен сәйкестендіру.

Production Trial Approval

Run the best dark-shade laboratory condition on the actual production machine.

Record:

  • Thickener grade and batch
  • Thickener dosage
  • Pigment product and dosage
  • Binder dosage
  • Final pH
  • Start / mid / end-run viscosity
  • Foam
  • Machine speed
  • Screen / squeegee settings
  • Solid-area coverage
  • Beginning-to-end shade
  • Penetration
  • Curing
  • Dry / wet rubbing
  • Fabric hand

Approve a dark-shade operating window—not one successful laboratory swatch.

Common Dark-Shade Troubleshooting Mistakes

1. Assuming Dark Shade Always Needs More Thickener

Viscosity can decrease, increase or remain acceptable depending on the pigment package.

2. Treating Pigment Dispersion as Pure Pigment

It also adds water, dispersant, surfactant and sometimes electrolytes.

3. Ignoring Binder-to-Pigment Ratio

Fastness may change when pigment rises without an appropriate binder review.

4. Restoring the Light-Shade Brookfield Number Blindly

The dark paste may print correctly at a different viscosity.

5. Ignoring Particle Loading

High pigment solids can increase apparent viscosity or modify flow behavior.

6. Testing Fresh Paste Only

Dark shades can develop delayed rheology or compatibility changes.

7. Increasing Defoamer Without Checking Pigment Surfactants

Dark-shade foam can originate from higher dispersion/surfactant loading.

8. Approving from One Black Pigment

Different pigment products can use different dispersant and surfactant packages.

Troubleshooting Table

Observed ProblemFirst Variables to CheckDo Not Assume
Dark shade becomes thinnerDilution, electrolytes, surfactants, pHMore thickener is automatically required
Dark shade becomes thickerPigment solids, particle crowding, associative interactionThe thickener batch changed
Dark paste has weak surface colorPenetration, transfer, pigment dispersion, K/SMore pigment is the first correction
Black solid areas look patchyScreen transfer, foam, rheology, pigment dispersionLow-shear viscosity alone defines coverage
Viscosity changes only after binderBinder-to-pigment ratio, electrolytes, surfactantsPigment loading alone caused the problem
Dark shade foams morePigment surfactant load, mixing, defoamerThickener is inherently foamy
Rubbing worsens in very dark shadeBinder level, curing, pigment/binder distributionThickener alone controls fixation
More thickener fixes viscosity but fabric hardensTotal polymer solids, binder, paste depositRestoring the light-shade number is necessary

Total Cost in Use

Dark-shade optimization should include more than pigment and thickener price.

A useful model is:

Cost per Saleable Unit = Total Attributable Production Cost ÷ Accepted Printed Output

Choose one denominator before comparing trials: accepted printed area in m² or accepted fabric mass in kg. Use the same fabric, design, quality criteria and costing boundary. Linear meters are comparable only when fabric width is also matched.

Cost componentCalculate in currency for the same trial or production run
MaterialsSum actual consumed quantity × unit price for pigment, binder, thickener and other auxiliaries. For a recipe estimate, thickener g/kg paste ÷ 1,000 × paste kg × supplied-product price/kg gives thickener cost. Reconcile actual use with returned or reusable paste.
Preparation and machine timeRecorded preparation, printing, cleaning and occupied equipment hours × the applicable cost rate. Lower speed or downtime changes these costs; efficiency is not a currency amount that can be added directly.
Energy, water and curingRecorded consumption × unit tariff, including the relevant drying, curing and any approved washing route.
Additional rework or disposalInclude extra material, time, energy and documented disposal costs attributable to the failed output.
Accepted outputUse only printed area or fabric mass meeting the agreed color, fastness, definition and hand criteria as the denominator.

Dosage is an input to material cost, not an additional cost term. Avoid double counting: if an equipment rate already includes labor or energy, do not add them again. Material and processing spent on rejected output are already included in the run’s numerator and its lower accepted-output denominator; add only separate losses not yet counted. This is a proposed comparison worksheet, not an FSX measured cost-saving result.

A lower-cost pigment dispersion can become expensive if it creates:

  • Higher thickener demand
  • More foam
  • More binder correction
  • Lower machine speed
  • Poor color uniformity

A higher-efficiency thickener can justify a higher price if it keeps dark shades stable with lower dosage and softer hand.

Compare cost per acceptable printed meter.

What Information Should You Send to a Thickener Supplier?

For useful dark-shade matching, provide:

  • Current acrylic thickener / TDS
  • Current thickener dosage
  • Viscosity and complete test method
  • Pigment product / color and dosage
  • Pigment solids if known
  • Binder grade and dosage
  • Fixer / auxiliaries
  • Final paste pH
  • Water hardness / conductivity if available
  • Мата
  • Flat or rotary screen
  • Holding time
  • Light-shade vs. dark-shade viscosity data
  • Main issue: viscosity, color yield, transfer, rubbing, foam or hand

FSX Chemical can use this information through Үлгілер мен сәйкестендіру to define a controlled pigment-loading and thickener-dosage comparison.

Шолу Synthetic Printing Thickeners және Textile Printing Thickener Applications for process-based matching.

How Should a Mill Optimize Acrylic Thickener for Dark Pigment Shades?

A practical decision chain is:

Define Light / Dark Reference → Measure Pigment Loading → Check pH / Dilution / Surfactants / Electrolytes → Build Pigment-Loading Curve → Hold → Print Fine Lines & Dark Solids → Adjust Thickener Only If Needed → Cure → Check Color / Rubbing / Hand

The key principles are:

  1. Higher pigment-dispersion dosage changes more than pigment concentration; it also changes the water, dispersant, surfactant and ionic environment.
  2. High pigment loading can decrease or increase viscosity depending on dilution, electrolyte effects, particle loading and associative interactions.
  3. Dark shades should not automatically use more thickener.
  4. Color yield depends on transfer, penetration and surface pigment concentration—not pigment dosage alone.
  5. Binder-to-pigment balance, foam and holding stability should be checked at the same time.
  6. The best dark-shade formulation is the one that remains inside the approved rheology and finished-fabric window at the lowest practical Total Cost in Use.

Frequently Asked Questions

1. Why does dark pigment paste become thinner?

If dispersion is added on top of an existing batch, dilution may contribute. At fixed final paste mass with make-up water adjusted, an unchanged thickener dose need not be diluted. Surfactants, dispersants, ions, pH and particle interactions can still alter rheology; check the actual mass balance and controlled comparisons before assigning the cause.

2. Can high pigment loading make the paste thicker instead?

Yes. Higher pigment solids can increase particle crowding, and associative thickener interactions can also raise viscosity in some formulas.

3. Should I always add more thickener for black pigment printing?

No. First measure the complete-paste rheology and printing result. Add more thickener only if the dark shade falls outside the validated production window.

4. Why can two black pigment dispersions give different viscosity?

They can contain different pigment solids, particle size, dispersants, surfactants, salts and pH-control chemistry.

5. Why can dark shades give weaker surface color than expected?

Excessive penetration, incomplete screen transfer, poor pigment dispersion or binder distribution can reduce surface color even when pigment dosage is higher.

6. Does higher pigment loading require more binder?

It may require a binder-ratio review to maintain rubbing fastness, but the correct level depends on pigment, fabric, binder chemistry and curing.

7. Why do dark shades foam more?

Higher pigment loading can introduce more surfactant/dispersant and can require longer or stronger mixing, increasing air entrainment and foam stability.

8. How can I tell whether viscosity loss is just dilution?

First check the final paste mass. Added dispersion can dilute an existing batch, while replacing make-up water at fixed final mass need not dilute the thickener. An equal-mass water addition is a screening control only; confirm carrier composition and other formulation effects before assigning the cause.

9. Should I test only the darkest shade?

No. A light–medium–dark ladder shows how the formula changes across the normal pigment-loading range and helps define a production window.

10. Why can HASE thickener behave differently at high pigment loading?

HASE uses hydrophobic association, so changes in pigment particles, dispersants, surfactants and binder can alter the associative network.

11. What should be checked after printing?

Evaluate print definition, solid-area uniformity, penetration, K/S or shade, dry/wet rubbing, foam-related defects and fabric hand after controlled curing.

12. What should I send FSX Chemical for dark-shade matching?

Send the current thickener/TDS, light and dark pigment dosage, viscosity method, binder, pH, water quality, machine route, holding time and the main color or rheology problem.

Match Acrylic Thickener to High-Pigment Dark Shades

If your light shades print well but black, navy or other dark pigment pastes become thinner, thicker, foamier or less uniform, FSX Chemical can help structure a controlled pigment-loading comparison.

For a useful technical review, send:

  • Your current acrylic thickener sample, TDS or COA
  • Current thickener dosage
  • Light- and dark-shade pigment products / dosages
  • Viscosity and complete test method
  • Binder grade and dosage
  • Fixer / auxiliary route
  • Final paste pH
  • Water hardness / conductivity
  • Fabric and screen-printing route
  • Holding time
  • Current color yield, transfer, rubbing, foam or hand target

Мынадан бастаңыз Үлгілер мен сәйкестендіру for a controlled current-vs-candidate evaluation.

Шолу Synthetic Printing Thickeners for the current FSX pigment-printing thickener route.

You can also Request a Factory-Direct Quote after the appropriate grade and dark-shade working dosage are confirmed or FSX Chemical-пен байланысыңыз for technical discussion📧 Электрондық пошта: Service@fsxchemical.com

The appropriate dark-shade dose is a validated operating range for the specific pigment, binder, fabric and process. Confirm that the selected production point maintains rheology, screen transfer, color, fastness and hand through the intended variation; one lowest passing laboratory point does not establish a universal minimum.

Жылдам байланыс

Талаптарыңызды жіберіңіз

немесе

Тегін үлгілер · 24 сағат ішінде жауап

Өнім туралы сұраулар және қолдау

Өнімге қойылатын талаптарыңызды жіберіңіз

Өнімнің атауын, қолдану саласын, мөлшерін, жеткізу орнын және сізде бар кез келген TDS, үлгі фотосуреті немесе құжатты жіберіңіз. FSX Chemical бұл ақпаратты қарап шығып, баға ұсынысын алу, үлгі сәйкестендіру немесе өнімді таңдау бойынша келесі қадамды ұсынады.

Өнім туралы ақпарат Өнімнің атауы, сорты, моделі, жапсырмадағы фотосурет немесе жеткізушінің сілтемесі.
Қолжетімді құжаттар TDS, SDS, COA, үлгі фотосуреті, өнім тізімі немесе сынақ деректері.
Тапсырыс мәліметтері Есептелген мөлшер, қаптама, тағайындалған ел, порт немесе сауда шарты.
Өтінім немесе мәселе Текстиль басу процесі, формулалау қажеттілігі, ағымдағы мәселе немесе мақсатты көрсеткіштер.