How to Measure Electrolyte Tolerance of a Synthetic Thickener for Pigment Printing

Electrolyte tolerance should be measured as viscosity and rheology retention under a clearly defined ionic...

Electrolyte tolerance is one of the most important performance properties of a synthetic thickener because a grade that builds high viscosity in clean water can lose much of its thickening efficiency after pigment, binder, fixer, hard-water ions or other auxiliaries are introduced. A useful test should therefore measure viscosity retention under controlled ionic stress rather than compare water viscosity alone. The most reliable qualification uses three levels: a simple reference-salt screening test, targeted challenges with relevant ions such as calcium or magnesium when needed, and final verification in the complete pigment-printing paste. pH, temperature, thickener dosage, salt basis, mixing sequence and equilibration time must be standardized before one grade is described as more electrolyte-tolerant than another.

How Do You Measure Electrolyte Tolerance of a Synthetic Thickener?

Prepare an electrolyte-challenged sample and a carrier-matched no-added-salt control at the same final batch mass and intended thickener concentration. Compare their viscosities at the same elapsed time using a defined method.

A practical calculation is:

Matched-reference retention (%) = challenged-sample viscosity at time t ÷ carrier-matched control viscosity at the same time t × 100.

But the number is meaningful only if the test also fixes:

  • Thickener dosage
  • Final pH
  • Su kalitesi
  • Salt type
  • Salt concentration basis
  • Mixing method
  • Equilibration time
  • Ölçüm sıcaklığı
  • Instrument / spindle / speed / reading time

A good qualification process uses:

Reference Salt Screening → Relevant-Ion Challenge → Complete Pigment-Paste Verification

This prevents a high water-viscosity grade from being incorrectly described as electrolyte-tolerant before it is tested in the real formulation.

Why Electrolyte Tolerance Matters in Pigment Printing

Acrylic synthetic thickeners are usually evaluated first in water because this makes thickening efficiency easy to see.

Production paste is much more complex.

It can contain:

  • Pigment dispersions
  • Binder emulsions
  • Fixers
  • Wetting agents
  • Defoamers
  • Hard-water ions
  • Neutralizer salts

These ingredients can change ionic strength and polymer interaction.

A grade that gives excellent water viscosity may therefore show:

  • Large viscosity loss
  • Slow viscosity drift
  • Different recovery
  • Poor screen behavior

inside the complete printing paste.

Electrolyte tolerance should therefore be treated as a separate performance property from water thickening efficiency.

Why Electrolytes Change Acrylic-Thickener Viscosity

Many synthetic acrylic thickeners contain ionized carboxylate groups after neutralization.

Those negative charges help keep the polymer chains expanded in water.

A simplified mechanism is:

Neutralization → Negative Charge → Electrostatic Repulsion → Polymer Expansion → Viscosity

When salts are added, dissolved ions can reduce the effective repulsion between charged polymer segments.

A simplified salt response is:

Electrolyte ↑ → Charge Screening ↑ → Polymer Expansion Can Decrease → Viscosity Can Fall

The magnitude depends on polymer architecture, salt type, concentration, pH and the rest of the formulation.

Therefore:

Water Viscosity ≠ Electrolyte Tolerance.

ASE vs. HASE: Why Salt Response Can Differ

ASE-type thickeners rely strongly on alkali swelling, chain expansion and hydrodynamic volume.

HASE thickeners add hydrophobic associative interactions.

Salt can therefore affect HASE through more than one route:

  • Charge screening
  • Polymer conformation
  • Hydrophobic association
  • Surfactant structure
  • Binder interaction

The HASE label describes an associative thickening route, not a transferable salt-tolerance specification. Measure the actual grade at the defined salt dose, pH and shear/time conditions; association and electrostatic effects can both affect the result.

Therefore:

HASE ≠ Automatically More Salt-Tolerant.

Test the actual commercial grade.

Where Do Electrolytes Enter a Pigment Paste?

Potential sources include:

  • Pigment-dispersion salts and dispersants
  • Binder-emulsion components
  • Cationic or ionic fixers
  • Neutralizer counterions
  • Calcium / magnesium from hard water
  • Other textile auxiliaries

The total ionic environment can therefore increase even when no ingredient is described simply as “salt.”

This is why electrolyte tolerance should be evaluated in stages.

Electrolyte Tolerance Is Not One Universal Number

A statement such as:

“This thickener tolerates 2% salt.”

is incomplete unless it also specifies:

  • Which salt?
  • 2% based on what mass?
  • What thickener concentration?
  • What pH?
  • What temperature?
  • What initial viscosity?
  • How long after salt addition?
  • What viscosity method?

Different laboratories can obtain very different “salt tolerance” values if these conditions are not standardized.

Use electrolyte tolerance as a defined test method, not a marketing adjective.

A Three-Level Electrolyte-Tolerance Test

LevelTest SystemPurpose
1Thickener + water + reference saltCompare response under a stated preparation and salt-test method
2Thickener + relevant Ca/Mg or process waterCheck plant-water robustness
3Complete pigment / binder / fixer pasteConfirm real production compatibility

All three levels answer different questions.

Do not use Level 1 to replace Level 3.

Level 1: Reference-Salt Screening

Reference-salt screening is useful for comparing several candidate synthetic thickeners under one controlled ionic challenge.

Use:

  • Same water
  • Same thickener dosage
  • Defined activation protocol appropriate to the grade and comparison purpose
  • Recorded pH conditions within the applicable grade window
  • Same salt
  • Same temperature
  • Same measurement method

For each salt level, prepare a separately balanced final test portion and its carrier-matched control. Record the no-added-salt result at the corresponding measurement time.

Challenge each portion by the documented feed and mixing procedure, then calculate the matched-reference ratio. A serial-addition experiment has cumulative dilution and shear history and should be reported as a different protocol.

A locked-SOP screen compares candidates under that SOP. If the SOP under-activates a candidate, report that limitation and run a separately documented grade-appropriate application comparison; a change in activation method or pH must not be attributed solely to polymer salt tolerance.

Which Salt Should Be Used for Screening?

Sodium chloride is often useful as a simple monovalent reference electrolyte because it is easy to prepare reproducibly and creates a straightforward ionic challenge.

However:

NaCl Screening ≠ Complete Pigment-Paste Simulation.

If the suspected production problem is:

  • Hard water
  • Calcium-rich process water
  • Magnesium-rich process water
  • A specific ionic fixer

then the next test should reproduce that relevant chemistry.

Use the reference salt for ranking, then use process-relevant ions for qualification.

Define the Concentration Basis Before Testing

Salt concentration can be reported on different bases.

Examples include:

  • Percentage of total test mass
  • Percentage relative to water phase
  • Mass per liter
  • Molar concentration

Pick one method and use it consistently.

For factory QC, a mass-based method can be convenient.

For scientific comparison between different salts, molar concentration or ionic strength can provide a more meaningful comparison.

Do not compare two test reports until the concentration basis is confirmed.

Build a Controlled Salt-Concentration Ladder

Do not test only:

0 Salt vs. One High-Salt Point.

Use several points across the relevant operating or stress range.

For each point, record:

  • Salt type
  • Salt level
  • Final pH
  • Viskozite
  • Viscosity retention
  • Görünüm
  • Foam / gel if present

Plot:

Electrolyte Level → Viscosity Retention

The curve is more informative than one pass/fail point.

It can show:

  • Gradual loss
  • Stable region
  • Sharp collapse threshold

Use process-relevant levels rather than copying arbitrary concentrations from an unrelated industry.

Calculate Salt Response with a Dilution-Matched Reference

A retention percentage is meaningful only when the compared samples have a defined composition, age and measurement method. Adding a salt solution to a finished paste also adds water; comparing that diluted sample with the untouched paste can wrongly attribute a dilution effect to salt.

Balance the final recipe first

Prepare the challenge and no-added-salt control to the same final mass and intended thickener concentration. Replace the salt stock solution with the appropriate carrier water in the control and account for all water in the recipe. Report salt dose as mass of the identified salt per final mixture mass, with purity and hydration state where relevant. State separately any concentration reported relative to polymer mass. These are different dose bases.

Matched-reference retention (%) = challenged-sample viscosity at time t ÷ carrier-matched control viscosity at the same time t × 100.

Measure both at the same elapsed time from addition, temperature, instrument geometry or spindle, speed, reading procedure and defined shear/rest history. Record pH and neutralization conditions. A before/after addition ratio instead uses the pre-addition sample as its denominator and combines electrolyte, dilution and time-history effects; label it separately and retain the carrier control. The ratios are not interchangeable.

Retain the absolute values

Hypothetical candidateControl viscosityChallenged viscosityRetention
A8,000 mPa·s4,000 mPa·s50%
B2,000 mPa·s1,600 mPa·s80%

These invented numbers illustrate the calculation only; they are not FSX test results or acceptance targets. B retains a larger fraction, while A has the higher final viscosity. Neither observation alone identifies the better printing paste. The required flow, recovery, screen transfer and finished-print result still determine suitability.

Do not calculate a meaningful ratio from a control at or near the instrument’s lower valid range. Report individual results and independently prepared repeats rather than hiding variability in one percentage. Set acceptance criteria for the actual process and include the complete pigment, binder and auxiliary package before production approval.

Control pH Before Comparing Salt Tolerance

pH-responsive acrylic thickeners must be compared at the correct activation condition.

If Candidate A is fully activated and Candidate B is under-neutralized, the test does not measure salt tolerance fairly.

Record:

  • pH before salt
  • pH after salt
  • pH after holding

Use each grade within its validated operating range.

Do not force every product to the same arbitrary pH if the suppliers specify different useful activation windows.

Doğru karşılaştırma şudur:

Each Grade Correctly Activated → Same Defined Electrolyte Challenge.

Control Temperature and Measurement Method

Every electrolyte-tolerance result should record:

  • Sıcaklık
  • Enstrüman
  • Spindle / rotor
  • Speed
  • Okuma süresi

A salt test measured at one temperature cannot be compared reliably with another sample measured at a different temperature.

FSX Chemical’s current thickener-testing guidance uses the same principle: viscosity becomes meaningful only when the measurement method is standardized.

Keep all candidate samples at the same test temperature before calculation.

Control Mixing and Equilibration Time

Viscosity can change during and after salt addition.

Standardize:

  • Salt-solution concentration
  • Addition rate
  • Mixing speed
  • Karıştırma süresi
  • Rest / equilibration time

If concentrated salt solution is poured into a thickener-rich zone, the local ionic concentration can be much higher than the final average.

This can create a stronger apparent shock than a well-mixed gradual addition.

Use the same addition procedure for every candidate.

Level 2: Calcium, Magnesium and Process-Water Challenge

If the mill uses hard water or sees factory-to-factory variation, the next test should include relevant hardness ions or real process water.

Compare:

  • Low-hardness reference water
  • Normal plant water
  • Representative harder-water challenge

If deeper diagnosis is needed, separate calcium and magnesium challenges.

Keep:

  • Final pH
  • Thickener dosage
  • Sıcaklık
  • Measurement method

constant.

This comparison can identify a different response to the defined Ca/Mg or process-water challenge. Plant water contains other variables, so a plant-water difference alone does not identify which ion caused it; use separate defined-ion tests when attribution matters.

Why Monovalent and Divalent Ions Should Not Be Treated as Equivalent

Sodium is monovalent.

Calcium and magnesium are divalent.

Divalent ions can interact more strongly with anionic polymer and dispersant systems.

Possible effects include:

  • Stronger charge screening
  • Polymer contraction
  • Changes in pigment dispersant behavior
  • Changes in binder colloidal stability

Therefore:

1% NaCl Test ≠ 1% CaCl2 Test.

The two salts do not provide the same molar concentration, ion valence or ionic strength.

Weight Percentage vs. Molar / Ionic Comparison

For production QC, weight percentage is often simple and practical.

For comparing fundamentally different salts, equal weight percentages can be misleading because:

  • Molecular weights differ.
  • The number of ions released differs.
  • Ion valence differs.

For technical R&D, consider comparing salts on:

  • Molar basis
  • Ionic-strength basis
  • Actual plant exposure basis

depending on the question.

For factory qualification, the most important test is still the real ionic environment the paste will see in production.

Level 3: Complete Pigment-Paste Verification

This is the production decision test.

Prepare the complete:

Water + Thickener + Pigment + Binder + Fixer + Auxiliaries

system.

Measure:

  • Viscosity before each major addition
  • pH
  • Nihai viskozite
  • Holding-time viscosity
  • Köpük
  • Gel / floc / separation
  • Screen behavior

The complete paste may behave differently from the simple NaCl test because:

  • Surfactants affect HASE association.
  • Binder particles interact with associative thickeners.
  • Pigment dispersants contribute ionic and colloidal effects.
  • Fixers can create strong local charge effects.

Use Level 3 for commercial approval.

Binder as an Electrolyte / Compatibility Challenge

Binder does not act like pure salt, but it can change the ionic environment.

It can introduce:

  • Su
  • Surfactants
  • Electrolytes
  • Polymer particles
  • pH shift

A difference from a carrier-water control shows a response to the complete binder package under that protocol. It does not by itself isolate electrolytes: binder particles, surfactants, pH and associative interactions can also contribute. Match final mass, thickener dose, elapsed time and addition/shear history, and record the binder’s water contribution.

Use:

Thickener + Equivalent Water

as a control against:

Thickener + Actual Binder.

Pigment Dispersion as a Formulation Challenge

Pigment dispersion can add:

  • Dispersants
  • Surfactants
  • Tuzlar
  • Su
  • Pigment particles

The actual commercial pigment-dispersion dose determines how much of this package enters the paste. Shade darkness alone is not a reliable dose measure across pigments, color strengths or recipes.

Therefore, electrolyte tolerance should be checked at representative:

  • Light pigment load
  • Normal pigment load
  • High commercial pigment-dispersion dose

if the plant uses a wide shade range.

Fixers and High-Ionic Auxiliaries

Fixers can create a strong ionic challenge even at a relatively small dosage.

If the fixer is cationic and the acrylic thickener is anionic, the problem may include both:

  • General electrolyte screening
  • Direct opposite-charge interaction

In that case, a simple NaCl curve cannot predict the complete behavior.

Test the real fixer at production-relevant levels and dilution conditions.

Addition Order and Local Electrolyte Shock

Electrolyte tolerance is affected by how the ionic ingredient enters the paste.

A concentrated salt or fixer solution poured into a poorly mixed thickener-rich zone can create:

  • Temporary extreme ionic strength
  • Local polymer contraction
  • Gel or floc
  • Irreversible-looking viscosity loss

For a fair test, standardize:

  • Pre-dilution
  • Addition rate
  • Feed point
  • Karıştırma

Production qualification should reproduce the actual addition method.

Holding-Time Viscosity Retention

Some electrolyte effects are immediate.

Others develop during holding.

Record:

  • Fresh viscosity
  • Intermediate viscosity
  • End-of-shift viscosity
  • pH
  • Sıcaklık
  • Görünüm

Calculate viscosity retention both:

  • Immediately after challenge, against its concurrently measured carrier-matched control
  • At each holding point, against a carrier-matched control held and measured over the same interval

A fresh passing result does not establish stability through the required holding period. Retain absolute challenged and control viscosities at every point. If also tracking drift against the challenged sample’s own first post-addition reading, label that within-sample holding ratio separately.

Measure Rheology, Not Only One Viscosity Value

Electrolytes can change:

  • Low-shear body
  • Kesme incelmesi
  • Elasticity
  • Yapısal toparlanma

In HASE systems, salt can change the balance between electrostatic swelling and hydrophobic association.

Therefore:

High Viscosity Retention ≠ Complete Rheology Retention.

For important candidates, compare:

  • Low-speed viscosity
  • Higher-speed viscosity
  • Post-shear recovery
  • Stringing / release if relevant

Connect Electrolyte Tolerance to Screen Printing

The best electrolyte-tolerant grade is not the one with the highest retained beaker viscosity.

It should also maintain:

  • Screen transfer
  • Yazdırma tanımı
  • Kontrollü penetrasyon
  • Katı alan homojenliği
  • Stable running

A candidate can retain viscosity but become too elastic or stringy.

Another can lose some viscosity yet remain inside the useful printing window.

Production performance determines whether the retention level is acceptable.

  1. Select the thickener candidate and confirm the correct activation method.
  2. Prepare all candidates at one defined water quality and test temperature.
  3. Record baseline pH and viscosity.
  4. Prepare one reference salt stock solution.
  5. Build a controlled salt-concentration ladder.
  6. Use identical addition, mixing and equilibration conditions.
  7. Record pH and viscosity at every salt point.
  8. Calculate the matched-reference ratio at each stated time and retain both absolute viscosities.
  9. Repeat selected candidates with process water / Ca / Mg if relevant.
  10. Repeat the most useful candidates in the complete pigment/binder/fixer paste.
  11. Check holding stability.
  12. Screen print and cure before final approval.

The method should be documented so incoming batches can be compared using the same procedure.

Synthetic Thickener Electrolyte-Tolerance Comparison Table

CandidateBaseline ViscositySalt ChallengeViscosity RetentionHeld RetentionComplete-Paste Result
ARecordDefinedCalculateCalculatePass / Conditional / Fail
BRecordDefinedCalculateCalculatePass / Conditional / Fail
TRecordDefinedCalculateCalculatePass / Conditional / Fail

Do not rank candidates only from baseline viscosity.

A lower-baseline candidate can be better if it remains inside the production window after the complete electrolyte challenge.

How Should Acceptance Limits Be Set?

Do not use a universal rule such as:

“A good thickener must retain 80% viscosity.”

That threshold may be too strict for one process and too weak for another.

Set acceptance from:

  • Historical successful production
  • Actual pigment / binder / fixer formula
  • Required screen behavior
  • Measurement repeatability
  • Finished-print quality

A useful specification can include:

  • Minimum retained viscosity under the defined test
  • No gel / floc / separation
  • Acceptable holding drift
  • Acceptable screen performance

The specification belongs to the test method, not the product name alone.

Can Electrolyte Tolerance Be Used for Incoming QC?

Yes, after a commercial grade has been approved.

A practical incoming or periodic application check can use:

  • Reference water
  • Fixed thickener dosage
  • Fixed activation method
  • One defined electrolyte challenge
  • Standard pH / temperature / viscosity method

Compare the new batch with:

  • Approved reference batch
  • Saklanan numune
  • Validated control range

Do not use an incoming salt test as the only release criterion.

Also verify identity, appearance, solids, pH and other agreed QC parameters.

Production Trial Approval

After laboratory ranking, run the best candidate in the real pigment-printing process.

Record:

  • Thickener grade / batch
  • Thickener dosage
  • Pigment / binder / fixer formula
  • Su kalitesi
  • Final pH
  • Start / mid / end-run viscosity
  • Bekletme süresi
  • Makine türü
  • Screen / squeegee conditions
  • Yazdırma tanımı
  • Penetrasyon
  • Color consistency
  • Dry / wet rubbing
  • Kumaş el

Approve the grade only if electrolyte tolerance translates into stable production performance.

Common Electrolyte-Tolerance Testing Mistakes

1. Testing Water Viscosity Only

High water viscosity does not prove salt tolerance.

2. Using One Salt Point Only

A concentration ladder reveals the stability region and collapse behavior.

3. Saying “2% Salt” Without Defining the Basis

The result cannot be reproduced unless the concentration basis is clear.

4. Comparing NaCl and CaCl2 at Equal Weight Percentage

The salts differ in molecular weight, ion valence and ionic strength.

5. Ignoring pH

Under- or over-activation can be mistaken for poor salt tolerance.

6. Measuring at Different Temperatures

Temperature changes apparent viscosity independently of electrolyte tolerance.

7. Ignoring Addition Order

Local electrolyte shock can exaggerate instability.

8. Calling a Grade Salt-Tolerant Before Complete-Paste Testing

Binder, pigment, fixer and surfactants can change the response significantly.

Troubleshooting Table

Observed Resultİlk Kontrol Edilecek DeğişkenlerVarsaymayın
Viscosity drops sharply after first salt pointpH, salt basis, activation, grade architectureThe test itself is correct
NaCl tolerance is good but plant paste still collapsesCa/Mg, binder, pigment, fixerNaCl predicts the complete formula
Ca/Mg challenge is much worse than NaClDivalent-ion sensitivityAll electrolytes are equivalent
Fresh retention is good but held viscosity fallsHolding chemistry, pH, temperatureImmediate retention proves production stability
Viscosity retained but screen release worsensElasticity, recovery, stringingRetention percentage defines printability
One binder causes much larger lossBinder electrolytes / surfactants / associationThe thickener alone is salt-sensitive
Diluted fixer is more stable than concentrated fixer additionLocal ionic / charge shockFinal dosage is the only relevant variable
Two labs report different salt toleranceSalt basis, pH, temperature, spindle, mixingThe products are necessarily inconsistent

Toplam Kullanım Maliyeti

Electrolyte tolerance affects cost through:

  • Thickener dosage
  • Formula correction
  • Water-treatment demand
  • Makine kararlılığı
  • Yeniden işleme
  • Quality loss

A useful model is:

Cost per accepted m² = monetary costs allocated to the agreed production boundary ÷ accepted finished-fabric area (m²). Price actual ingredient consumption and water treatment, then allocate preparation, printing and finishing with stated rates. Use one currency and count rework or disposal charges once; do not add rejected material value again if it is already included in consumed ingredients. Track unpriced stability or downtime separately. A linear-metre comparison is usable only at an equivalent defined fabric width.

A higher-priced synthetic thickener can be more economical if it:

  • Retains viscosity at lower dosage
  • Handles the real binder/pigment ionic load better
  • Reduces correction additions
  • Improves long-run consistency

Compare the validated production cost, not only water viscosity or price per kilogram.

What Information Should You Send to a Supplier?

For useful electrolyte-tolerance matching, provide:

  • Current synthetic thickener / TDS
  • Thickener dosage
  • Activation method and pH
  • Viskozite ve tam test yöntemi
  • Current electrolyte-tolerance test method if any
  • Pigment product and dosage
  • Binder grade and dosage
  • Fixer / ionic auxiliaries
  • Water hardness / conductivity
  • Bekletme süresi
  • Flat or rotary screen
  • Observed failure: viscosity loss, drift, floc, screen instability or cost

FSX Chemical bu bilgileri şu yollarla kullanabilir: Numune ve Ürün Eşleştirme to structure a controlled candidate comparison.

İnceleme Sentetik Baskı Kıvamlaştırıcıları, Textile Printing Thickener Testing Parameters ve Why Synthetic Printing Thickener Loses Viscosity After Pigment, Binder or Electrolytes for related selection logic.

How Should a Mill Define Electrolyte Tolerance for Synthetic Thickener?

A practical control chain is:

Correctly Activate the Grade → Standardize Water / pH / Temperature → Build Reference-Salt Ladder → Calculate Viscosity Retention → Challenge Relevant Ca/Mg or Process Water → Test Complete Pigment/Binder/Fixer Paste → Hold → Screen Print → Define Production-Based Acceptance Limits

Temel ilkeler şunlardır:

  1. Electrolyte tolerance is a defined test result, not a generic product claim.
  2. Water viscosity and salt tolerance are separate thickener properties.
  3. NaCl is useful for controlled screening, but it does not reproduce every process electrolyte.
  4. Divalent ions such as calcium and magnesium should be challenged separately when hard water matters.
  5. pH, temperature, salt basis, mixing and equilibration must be standardized before candidates are compared.
  6. The commercially useful grade is the one that remains inside the complete-paste rheology and printing window at the lowest practical Total Cost in Use.

Sık Sorulan Sorular

1. What is electrolyte tolerance in a synthetic thickener?

It is the ability of the thickener to maintain useful viscosity and rheology when dissolved ions or ionic formulation components are present.

2. How do I calculate viscosity retention?

For the matched-reference result, divide the challenged viscosity by its carrier-matched no-added-salt control measured at the same elapsed time, then multiply by 100. Match final mass, thickener concentration and the stated measurement/shear history. A pre-addition denominator gives a different before/after ratio and must be labelled separately.

3. Is sodium chloride a good salt for electrolyte-tolerance testing?

It is useful as a reproducible monovalent reference salt, but it does not replace testing with hard-water ions, binder, pigment or fixer when those are the real production stresses.

4. What salt concentration should I use?

There is no universal concentration. Build a ladder around the actual process range or a technically justified stress range and clearly define the concentration basis.

5. Is HASE always more electrolyte-tolerant than ASE?

No. HASE adds associative thickening, but salt response depends on hydrophobe architecture, pH, surfactants, binder and shear conditions.

6. Why can calcium or magnesium be more problematic than sodium?

Ca²⁺ and Mg²⁺ are divalent ions and can affect anionic polymers, dispersants and colloidal stability differently from monovalent sodium ions.

7. Should NaCl and CaCl2 be compared at the same weight percentage?

Not for a rigorous scientific comparison. They differ in molecular weight, ion valence and ionic strength. Factory tests should instead reproduce the actual process exposure or use a clearly defined comparison basis.

8. Why does the thickener pass the salt test but fail after binder is added?

Binder adds water, surfactants, electrolytes and polymer particles, and HASE-type thickeners can also interact associatively with the binder.

9. Should electrolyte tolerance be measured immediately or after holding?

Measure both fresh and at the relevant holding points, with a concurrent carrier-matched control at every point. Record the absolute viscosities as well as the ratios; a fresh ratio alone cannot establish stability during production.

10. Can I use electrolyte tolerance for incoming QC?

Yes, after the grade and method are validated. Use one standardized challenge and compare new batches with an approved reference, together with other agreed QC checks.

11. What is a good viscosity-retention percentage?

There is no universal percentage. The acceptance limit should come from successful production data and the minimum rheology needed for the actual printing process.

12. What should I send FSX Chemical for electrolyte-tolerance matching?

Send the current thickener/TDS, dosage, activation pH, viscosity method, pigment, binder, fixer, water hardness/conductivity, holding time and any current salt-test data.

Compare Synthetic Thickeners Under the Electrolyte Conditions That Matter

If a synthetic thickener builds strong viscosity in water but becomes unstable after pigment, binder, fixer or hard process water is added, FSX Chemical can help structure a controlled electrolyte-tolerance comparison.

For a useful technical review, send:

  • Your current synthetic thickener sample, TDS or COA
  • Thickener dosage and activation method
  • Final pH
  • Eksiksiz viskozite test yöntemi
  • Current salt-tolerance method if available
  • Pigment and binder products / dosages
  • Fixer / ionic auxiliaries
  • Water hardness / conductivity
  • Bekletme süresi
  • Current viscosity-retention or production-stability problem

Şöyle başlayın: Numune ve Ürün Eşleştirme for a controlled current-vs-candidate evaluation.

İnceleme Sentetik Baskı Kıvamlaştırıcıları for the current FSX textile-printing thickener range.

Ayrıca şunları da yapabilirsiniz: Fabrikadan Doğrudan Fiyat Teklifi İsteyin after the suitable grade and electrolyte-tolerance working window are confirmed or FSX Chemical ile İletişime Geçin teknik tartışma için📧 E-posta: Service@fsxchemical.com

A meaningful electrolyte-tolerance number is never just “how much salt the thickener can take.” It is the viscosity and rheology retained under a clearly defined salt, concentration basis, pH, temperature, mixing and holding method—and finally the performance retained in the complete production paste.

Hızlı Bağlantılar

Hızlı İletişim

İhtiyacınızı Bildirin

veya

Ücretsiz numuneler · 24 saat içinde yanıt

Ürün Soruları ve Destek

Ürün İhtiyacınızı Bildirin

Ürün adını, uygulama alanını, miktarı, teslimat yerini ve elinizdeki TDS, numune fotoğrafı veya belgeleri paylaşın. FSX Chemical bu bilgileri inceleyerek fiyat teklifi, numune karşılaştırması veya ürün seçimi için bir sonraki adımı önerecektir.

Ürün Bilgileri Ürün adı, sınıfı, modeli, etiket fotoğrafı veya tedarikçi referansı.
Mevcut Belgeler TDS, SDS, COA, numune fotoğrafı, ürün listesi veya test verileri.
Sipariş Detayları Tahmini miktar, ambalaj, varış ülkesi, liman veya teslim şekli.
Uygulama veya Sorun Tekstil baskı süreci, formülasyon gereksinimi, mevcut sorun veya hedeflenen performans.